TURBOMACHINERY SPEED MEASUREMENT
Steam turbine speed sensor failure


Speed measurement instruments for a rotating machine are essential to ensure proper control and protection.


System architecture

In this steam turbine application, 2 sensors were installed for speed control and 3 sensors for overspeed protection.

Some details on the redundancy of the system:

-          Turbine control. The sensors are read in through a single CPU. Therefore, the two sensors are operated in 1-in-2 logic, i.e. in the event of a fault, and therefore with only one sensor in operation, the turbine continues to be regulated. In this case, the speed controller selected is a Woodward Flex500.

-          Protection. The overspeed system consists of 3 independent modules, each with a redundant power supply and 1 independent speed measurement. In this case the degree of redundancy on the measurement is threefold and we speak of logic 2 out of 3, i.e. the instrument only commands a stop when at least two sensors detect a high level, but not if only one detects it.  The overspeed system is assigned to the Woodward ProTech GII.

 
Event analysis

Following maintenance, the sensor connectors, which were loose in the rotating case, were sheared off by the phonic wheel itself at the first turbine rotations.

The control system, as well as the overspeed device, immediately recognized the lack of measurement and commanded a turbine stop.

When the sensor box was opened, the fault was evident, and the sensor connectors were replaced.

Once the normal operating condition was restored, it was possible to start the machine.

 

Safety logic

In this project, the following safeties were active on the machine:

-          overspeed. Constant monitoring, in each machine sequence, of the turbine speed against the set overspeed threshold.

-          wire break detection. A dedicated speed measuring circuit ensures an electrical continuity check on the measuring circuit for passive speed sensors such as magnetic/variable reluctant sensors.

-          loss of speed. In any operating condition, a drop in the speed measurement below a minimum speed threshold causes the immediate stop.

-          Speed discrepancy. Speed measurement discrepancy between the measurement sampled by two sensors causes immediate failure of the measurement loop that transmits the lower measurement, thus ensuring a measurement based on the highest signal.

-          Over-acceleration. The system triggers an immediate turbine shutdown to anticipate the overspeed condition based on measured acceleration.

Woodward has distinguished itself over the years for high standards in the control of turbomachinery.  The control and protection features described in this article are available on the Woodward control catalogues.

To learn more about turbomachinery protection and control techniques, contact us or request a course from one of our specialists.

in News
Black smoke at startup
Troubleshooting and solving of excessive smoke during emergency generator start-up
Contact us
Turner ECS Netherlands

Dirk Storklaan 76
2132 PX Hoofddorp
The Netherlands
Tel: +31 (0) 23 566 23 00

24/7: +31 (0) 6 57 59 22 50
info.nl@turner-ecs.com

Unit 1 High Carr Business Park
Newcastle-under-Lyme
Staffordshire ST5 7XE
United Kingdom
Tel: +44 1782 569190
info.uk@turner-ecs.com

Turner MCS Italy

Polo Tecnologico della Brianza Edif. 9 Lab 3
Via Lavoratori Autobianchi 1
20832 Desio, Italy
Tel: +39 0362 62 12 40
info.it@turner-mcs.com

Turner ECS Germany

OhmStraße 2
D63225 Langen
Germany
Tel.: +49 (0) 6103 73 299 0
info.de@turner-ecs.com

Turner ECS Abu Dhabi

Bin Hamoodah Building
7th Floor, Sh. Khalifa Street
P.O. Box 203, Abu Dhabi
United Arabic Emirates
Tel: +971 02 626 7912
info.me@turner-ecs.com

Turner ECS Saudi Arabia

Office No. 702
7th Floor Al Mousa Tower
6682 Al Amir Turki-Al Yarmok Dst.
Al Khobar - Saudi Arabia
General: +966 138343734

Mobile: +966(0)504827421
info.me@turner-ecs.com

Turner ECS Qatar

P.O Box 153
Ein Khalid Commercial Building
Doha, Qatar
Tel: +974 3338 0351
info.me@turner-ecs.com